Ford Flathead V-8 History for this weekend

Posted on December 1, 2018January 30, 2020 by Steve Carpenter

01 Dec

Ford Flathead V8 Engine History

Many people mistakenly believe that the Ford flathead V-8 was the first V-8 engine. It proved to be extremely popular until the overhead valve engines arrived and was the first V-8 readily available to the masses, but it was not the first. Léon Levavasseur took out the first patent for a V-8 gasoline engine in 1902. Although not a production engine, it was utilized in several aircraft and competition speedboats of the day. Meanwhile, American motorcycle builder and aviation pioneer Glenn Curtiss installed one of his 269-ci aircraft V-8s in a motorcycle and set an unofficial land speed record of 136.36 mph in 1906.

Britain’s Rolls-Royce created the first automotive V-8, but only three were produced, in 1905 and 1906, before Rolls-Royce reverted to its trusted straight-6. In 1910 French automobile and railcar manufacturer De Dion-Bouton unveiled a 474-ci automotive V-8, which it displayed in New York in 1912. Although few were actually produced, they served as inspiration for several U.S. manufacturers.

W. R. Campbell, president of Ford Motor Company Canada, stamps the first V-8 produced in Windsor, Ontario. Note the early long-neck water pumps. Canadian blocks were produced until 1954, as were Australian blocks. (Photo Courtesy Fordimages.com)

Cadillac, for example, sold 13,000 flathead V-8 vehicles in 1914. The Cadillac was a sophisticated unit with cast-iron, paired, closed-head cylinders bolted to an aluminum crankcase, and it used a flat-plane crankshaft. Many historians consider this to be the first true production V-8 automotive engine.

General Motors was quick to follow Cadillac’s success with a flathead V-8 for Oldsmobile in 1916. The next year saw Chevrolet follow suit with a 288-ci engine for its Series D autos. When Chevrolet became part of General Motors in 1918, however, its V-8 was discontinued in favor of more economical engines.

Across town at Highland Park, Henry Ford had been experimenting with V-8 engines as early as 1922 (he didn’t like to follow the competition), but by 1928 he had decided, “to go from a four to an eight, because Chevrolet is going to a six.”

Ford engineers gathered up the competitors’ V-8s, including one of their own Lincolns (Lincoln had introduced a V-8 in 1921, the year before Henry Ford purchased the company), but they were complicated assemblies with separate cast barrels bolted to a crankcase. Ford wanted something much simpler for the new car he was developing to replace the Model A. Ford had been able to cast the Model T cylinders and crankcase en bloc (that is, in one piece), and he wanted the same mono construction for his V-8.

To begin, Ford engineers came up with two designs, one of 299 ci and another of 232 ci designated Model 24, which Henry eventually chose. The first engine ran at the beginning of 1931, and soon more were assembled and installed into Model As for testing.

The first mass-produced monobloc V-8, with a cam-driven distributor and integral coil, went into production on March 9, 1932. (Photo Courtesy Fordimages.com)

Eventually known as the Model 18 (1 for first and 8 for, well, eight cylinders), the new Ford V-8 was unique. In addition to the revolutionary, one-piece casting, Ford wanted the exhaust passage running through the block for quick warm- ups because it gets cold in Detroit. A quick warm-up notwithstanding, Ford demanded that his engineers use existing Model A water pumps to save development and tooling costs. He wanted a thermosyphon system, whereby the pumps acted only to accelerate the flow of water.

A thermosyphon system acts on the principle that hot water seeks a higher level than cold water. Consequently, when the water reaches approximately 180 degrees F, circulation commences. The

water flows from the lower radiator outlet pipe, up through the water jackets, into the upper radiator water tank, and down through the tubes to the lower tank to repeat the process.

Unfortunately, because of Ford’s demands, the V-8 suffered overheating problems until the 1937 redesign. Ford also wanted to eliminate the gears used to drive the distributor. Rather, he wanted the distributor bolted to the front of the block and driven directly by the camshaft, which itself was gear-driven and located above the crank. Ford did not want to give up the Model A’s gravity-fed fuel system. However, he had to relent and have a fuel pump that would suck fuel from a rear-mounted tank.

Growing Pains

Although the Ford flathead V-8 was produced virtually unchanged in concept from 1932 to 1953, it wasn’t an instant success. It was put into production perhaps too quickly, and there were numerous problems. Nearly all of the first 2,000 engines needed their cams, valves, valve-guides, and front covers changed. The next 2,000 also needed repair, and most of the first 4,250 cars assembled were used as demonstrators and not sold to the public. Many cars were fitted with the more reliable 4-cylinder engine. Teething troubles aside, Ford produced 212,238 V-8s between production start-up in March 1932 and December 1932.

This cutaway engine was photographed on May 12, 1932, for display in France. Thank goodness for the French and their long association with the flathead. (Photo Courtesy Fordimages.com)

Oh for a day in the engine testing room in 1934 when this photograph was taken. Most of the engines have aluminum heads, but a few iron-head versions are down the middle. (Photo Courtesy Fordimages.com)

Although not immediately adopted by racers, a few flathead Ford V-8s appeared at Indianapolis. Chet Miller drove this nice roadster, entered in the 1934 race by the Bohn Aluminum & Brass Company. It had what was undoubtedly the first flathead V-8 speed equipment: Bonalite aluminum heads and a brace of Stromberg 97s sideways atop a Don Sullivan intake. Apparently it produced 140 hp and achieved 109.252 mph, but it sailed over the wall on the 11th lap. (Photo Courtesy IMS Photo)

All domestic V-8 engines were produced at Ford’s River Rouge Plant, southeast of Detroit, and shipped to other assembly plants. Eventually, engines were built in other countries, including Canada and Great Britain. Until 1941, all Rouge-produced V-8s were painted Ford engine green before machining. Stamped parts were painted black, and cast-aluminum parts were unpainted. Colors changed over the years, so do not use engine color as a guide to the date of manufacture.

There were problems with the fully floating main bearings and lubrication system, and throughout 1932 a flow of factory service letters detailed fixes. (“Fully floating” means that not only did the rods rotate on the bearing, but the bearings also rotated on the crank; consequently, all three components were freely, or fully, floating.) Excessive oil consumption was a problem. Some cars used a quart of oil every 50 miles. The dipstick was made 1 inch short to prevent the public from operating cars with insufficient oil. In fact, between 1932 and 1935, five different oil indicators were used with various pan designs.

Piston wear was another issue. Early pistons, from 1932 to 1935, were aluminum alloy, but in 1935 steel dome pistons were put in limited use. They were standard on all engines from April 1936 until 1938.

Because the water pumps were located in the cylinder heads, they supposedly pulled heated water from the block (but were really sucking hot air). Because there were no thermostats, the engine overheated. Consequently, a new four-blade fan, larger pulley, and larger radiators were introduced, and more louvers were punched in the hood, increasing the number from 20 to 25 (the last louver was closed off). However, Henry Ford ignored the real reason for overheating: the water pump’s location.

Despite its 65-hp rating, the 221-ci V-8 was not initially popular with the racing fraternity, which preferred the tried-and-tested T and A 4-bangers. Meanwhile, Ford continued refinement: New for the 1933 Model 40 were lightweight aluminum heads that allowed for an increase in compression ratio from 5.5 to 6.3:1. In addition, a limited production of engines included Holley carbs.

By 1934 most of the teething problems had been remedied, and a good V-8 could produce 90 hp, return about 20 mpg, and hit 90 mph. In the hands of speed merchants, it could go much faster. By the end of 1934, Ford had produced 1,352,202 V-8 engines.

In 1935 the V-8 block was significantly changed to accommodate flow-through, or positive crankcase ventilation. The new block was given the prefix 48 for its part number. Domed pistons were installed, and new casting technology allowed for a cast-alloy steel crank to replace the earlier forged cranks. The year 1935 was also significant because the 2 millionth V-8 car rolled off the production lines. The following year, the 3 millionth was produced. Also new for 1936 were shell-type main bearings, replacing the previous poured white-metal Babbitt bearings. A more economical dual-throat Stromberg 97 carb replaced the Detroit Lubricator, and a new fuel pump was introduced. That same year, Ford applied for a license to build a two-seater light air- plane powered by an aluminum V-8; 10 of these were reportedly built.

Surviving the Great Depression

The big change came in 1937, when the water pumps were finally moved to the upper front of the block (the inlet side of the system), thus drawing cool water from the radiator rather than trying to suck hot water out of the block. The water outlets were also moved rearward, to the center of the head. Some early versions had blanking plates on the block. The engine, which now produced 85 hp, was designated V-8-85. Some later catalogs, however, erroneously listed it as producing 90 hp.

Vic Edelbrock was one of the first to see the potential of the speed equipment business. He experimented with his own parts even before World War II. Here’s a Bay Area hot rodder with Edelbrock heads and intake with three deuces. (Photo Courtesy GhostracksUSA.com)

Also new in 1937 was the compact version of the V-8, the V-8-60. Known as the “thrifty sixty,” this 60-hp V-8 was a mini version of the V-8-85 and returned 25 mpg; it was Henry’s answer to requests for a six. It caught on with midget racers and in some overseas markets, such as France and Great Britain, where there was a horsepower tax. However, it never really found favor in the United States, where it was underpowered for the weight and size of the average car. It was discontinued in the United States in 1940.

As the world struggled out of the Great Depression the initial problems with the V-8 were gradually eliminated. Ford was able to increase production as he had with the Model T and, to a lesser extent, the Model A. He unwittingly gave auto racers access to a cheap, high-performance engine that at last was attracting the attention of the speed merchants.

One of the first to see the potential was Vic Edelbrock, who purchased a V-8 Deuce Roadster in 1938. It became his daily driver, his test bed, and his lakes racer. Fitted with 21-stud cast-iron Arco milled and filled Denver heads, it sported a Winfield cam, a Thickstun manifold, Sandy’s headers, and dual ignition. It was the portent of a burgeoning post–World War II industry. By the end of 1937, Ford had produced 4,438,368 V-8 engines.

Ford announced another block modification for 1938. This was, of course, big news. It changed from 21- to 24-stud cylinder heads with 14-mm spark plugs. The main bearing sizes were also increased. Due to the slow introduction of the 24-stud block, the 1937 block assembly was continued until June 1938. (Until the introduction of the 24-stud block, Vic heads had been interchangeable left to right, right to left. With the 24-stud pattern, heads were no longer interchangeable.)

In 1939, the Mercury brand was introduced to fit between the low-priced Ford and the high-end Lincoln. Although Ford stayed with the 3.0625-inch bore, the Mercs had a 3.1875-inch bore for 239 ci. The Merc version of the flathead also had larger-diameter crank bearings, heavier rods and crank, and other strengthened components.

Building Up to the End

Because of World War II, very little changed from 1941 onward. However, as a result of Ford’s engineering developments during the war, the V-8 saw some minor but significant refinements. In addition, the new Model 59A engine was used in identical forms in both 1946 Ford and Mercury models. New tri-alloy bearings (derived from aircraft) combined with higher-octane fuels resulted in a rise in compression ratio to 6.8:1 and an increase from 90 to 100 hp. Also new were four-ring pistons, aluminum cam gear, and a higher-capacity oil pump; it all contributed to a much-improved powerplant. (The 1932–1948 cam gears were cut in the opposite direction as 1949–1953 gears. Be careful not to buy the wrong set for your rebuild.)

Barney Navarro, who started in the performance business machining Weiand speed equipment, began his own business in 1947. He improved on everything his hands touched and was a pioneer in the evolution of the performance flathead. (Photo Courtesy H&H Flatheads)

Barney works on the 1927 Ford Roadster that he raced at the dry lakes. It sports his cast-aluminum dual intake manifold and finned heads. He also experimented (successfully) with mixing alcohol and oxygen. (Photo Courtesy H&H Flatheads)

A rare shot of the French military Simca V-8. It’s similar to an 8BA in that it has thermostats in the heads and an angled distributor with an external coil, but it retains the integral bellhousing and a cast-aluminum pan. (Photo Courtesy Stephan Szantai)

Barney, seen here at Los Angeles’ Carrell Speedway with Tom Beatty and George Pounden (right), was one of the first, if not the first, to bolt a GMC blower atop a flathead. Four Stromberg 97s fed the quad-belt-driven 3-71. (Photo Courtesy H&H Flatheads)

Of course, the end of World War II saw thousands of returning U.S. servicemen looking for work and excitement. Many, including Barney Navarro and Al – Sharp, found what they were looking for, building speed equipment and racing the flathead Ford V-8. A $40 billion industry carried on by men such as Mike Herman at H&H Flatheads was being born.

In 1948, the V-8 fitted to Mercury automobiles was given a 4-inch-stroke crank that resulted in 255 ci. Ford engines retained the 3.75-inch stroke for 239 ci. Many other changes were made, some obvious and some not. The heads were now held down with bolts rather than studs and nuts. The water outlet fittings were moved from the middle to the front corner of the head. A major change was a new distributor, still driven from the cam but now through a shaft mounted at right angles to the engine’s axis. Also, the bell-housing was no longer an integral casting with the block. Instead it was a bolt-on piece.

Internal changes included straight-stem valves with one-piece guides. In general, these later Ford engines were commonly referred to as 8 BAs and their Mercury counterparts as 8CMs. Later, 1952–1953 Fords were referred to as EABs while the Mercs were EACs. These engines did not have the hardened valve-seats like the earlier engines. The markings were usually cast in the head.

Ford also introduced a large displacement 337-ci version in 1948, primarily for the truck market. However, when Lincoln was unable to produce the V-12 it wanted for its 1949 model, the 337 V-8 was adapted. In 1952, the Lincoln Y-block replaced the 337. Unfortunately, the 337 is not a great-looking engine and never found much favor outside the restoration market.

For the 1952 Ford passenger car model year, the company introduced a new overhead valve (OHV) Mileage-Maker 6-cylinder. Developing 101 hp, the OHV 6 outshone the V-8. Consequently, Ford increased the V-8’s compression ratio to produce 110 hp. Nevertheless, the writing was on the wall, and 1953 was the last year of the flathead Ford V-8 in the United States.

After 21 years of continuous improvement and production, the venerable Ford flathead V-8 ceased production. Well, in the United States at least. The flathead design was produced in Canada until 1954. It was licensed to a French manufacturer for use in the Simca brand until 1961, in Brazil until 1964, and until 1990 in the Simca Unic Marmon Bocquet military truck.

I had one of these engines and put it in my Model A Roadster back in about 2006.

Many Moons ago but I have my 1928 AV8 here and wanted the 1940’s look and feel to it, my reasoning is that, I grew up by the ww2 runways of the USAF and wanted to use original parts to the Roadster, that way it will not only look the same but- I will experience exactly what they did after the war.

Love this ride and even though it has its hiccups, I wouldn’t want it any other way to be honest.

Mine has a 39 Ford Mill and Gearbox, but plans for some more Hop Up parts later, the Edelbrocks are fine and run Two 97’s.

RPM HOT ROD NATIONALS OCTOBER 28th Santa Margarita Ranch

Posted on October 3, 2017January 30, 2020 by Steve Carpenter

03 Oct

For those of you like me that are into many Vintage things, well, this is a great event to head to, I wont have my Model A Roadster Completed for this but will be for next year but am still driving up there with Jennifer to watch the 1/8th miles Nostalgic races as the countryside is amazing there and will be riding our Triumphs around that area, so what better weekend away than to explore Santa Margarita ranch and watch the 4 Bangers and Flatheads on the old Tarmac.

Hope to see you there.

RPM Nationals is a race that pays homage to the early days of drag racing. When race cars and street cars competed head to head to see whose garage built hop up was the fastest. The races then started with the drop of a flag and end 1/8 of a mile down the strip.

We will have 3 brackets competing head to head including v8s, 4 Bangers and full race.

Where?

Santa Margarita Ranch

9000 Yerba Buena Ave

Santa Margarita, CA 93453

EVENT DETAILS

RPM Nationals Takes place on October 28th 2017 at Santa margarita ranch in Santa Margarita California. Enter the ranch off of Yerba Buena. Gates open at 9am and racing starts shortly there after. racing continues throughout the day with the finals in each bracket concluding by 6pm. There will be music, vendors selling food, clothing and aftermarket speed parts. We will also be doing a swap meet section reserved for vendors selling period correct, rpm nationals applicable hot rod parts. If you are interested in being a vendor or swap meet vendor email rpmnationals@gmail.com for more info

There will be absolutely no outside alcohol allowed at the event and cars will be checked upon arrival. There is also no BBqing/open flames or smoking due to wildfire risk. Please respect the ranch and clean up after yourself. Inappropriate behavior will be followed up by immediate removal from the premises.

Race Car Requirements

RPM Nationals is limited to ford Flathead and 4 Cylinder cars. Body Years are limited to 1936 and earlier . All Cars must represent an early 1950s Hot rod style or prior. Things like radials, billet, etc… will not be allowed. All racers must apply prior to registration for approval to race. rpm nationals has the final say in all race cars approval. Racers must wear and provide their own helmets.

Classes– There will be 3 race classes… 4 Cylinder Street Cars, V8 street cars and full race class. Cars with Power adders such as Blowers and overhead conversions will be considered full Race.

All cars must pass a technical inspection to ensure its safety and are required to run hub retainers, dual throttle return springs, seat belts, water overflow catch and must run water; no coolant allowed. Cars must in good general condition; tech has the final say on all race cars.

All applicants must email rpmnationals@gmail.com by September 22nd 2017 for approval. Please provide a spec sheet outlining all major components and photos of the cars front, back, both sides, engine and drivers compartment.

we will notify all Applicants by the 29th of September. Upon approval racers must sign and return their release form along with payment of $70 no later than October 10th.

RPM Nat’s Car Show

we will also be having a large car show at RPM Nationals. The car show is open to all hot rods and customs model year 1960 or before. . the cost to bring a car to show is just $25, the cost of general admission. we will be picking best hot rod and best custom and a number of clubs will be picking their favorites and providing trophies.

VENDORS

There will be a sizable location at the RPM Nationals race for vendors selling food, new aftermarket hot rod parts and accessories, clothing, collectibles and other products. We can accommodate booths ranging in size from 10 feet x 10 feet and up depending on the vendors needs. All vendors are required to have their own event insurance coverage. Email rpmnationals@gmail.com if you are interested in being a vendor.

SWAP MEET

Clean out those garages! The swap meet area is reserved for people selling used early ford parts and speed parts only. no selling of new products or parts allowed in the swap meet area. Swapmeet spaces are $40 per car/truck load and an additional $20 for trailers. This fee includes one admission ticket. Email RPMnationals@gmail.com if you are interested in reserving a Swapmeet space.

For more information Email: rpmnationals@gmail.com

rpm11

Bonneville Salt Flats part 2

Posted on September 2, 2017January 30, 2020 by Steve Carpenter

02 Sep

OK, the previous Blog took me so long as the photos were high quality and the download time kicked me right in the Spuds, but, I have a few more photos left but these I took with my phone, so not great clarity, but wanted to share a few more photos of the great times Jennifer and I had at Speed Week in Bonneville.

Above is this A-Bone Pick up, as we all hung out outside the Nugget Casino and Hotel in the evenings, this was a super place just to have a beer and look at other peoples rides, chew the fat with many people that had traveled from all over the globe and we all had one thing in common and that was of course Speed Week.

Check out this Pick up, very cool and old school as it had swooping fenders with rear skirts, a lot of work went into this rig and I sure loved the way it sat in the weeds, great job of it.

Envious of the Hop Up coupe, just take a llok at this really Period machine, I mean sat on cross ply 16 inch Firestone’s on 40 ford steelies and unchopped too, such a treat for me to see this.

Just when you think you have seen it all, this El Gringo loco truck was just bad ass, very cool, I am sure it bumped around on the tarmac but loved the style of this pick up.

Studebaker trucks have always been cool, almost Custom from the factory, I see this has old school ribbed bumpers and sporting 2 sets of 1939 tear drop lights at the rear, tight looking rig.

My God, Drool factor is off the hook, this Brown Suede Oxide three window was the epitome of Hot Rodding, complete with Black-walls and Stainless Hair pins, I just loved looking at this, Schroeder Race track steering box too as you can see the Pittman arm hanging out the side of the cowl.

I loved this three window as it even had an original 1932 Utah License Plate, what is not to like about this really Nostalgic Hot Rod.

How about this for a sight for sore eyes and when I say sore eyes, thats from the blinding glare off the Salt Flats today, the Rolling Bones Club drove down and they took their rides onto the Lake and when they came back each night, they pulled in at the Nugget, what a super rare sight it is to see all this Hot Rods in one place and covered in salt too. GULP!

This Slammed Hemi powered 5 window was popular with many people, the owner was super cool to chat too, as were everybody at this event, something a few events dont have any more and this place was ooozing with Camaraderie.

Just look at this sight, so much rare tin and not many places you will see as many as this in one place, it was Hot Rod heaven with out a doubt and I enjoyed every minute of it.

More salt sprinkled here than a bag of English fish and chips and every one of these rides had Salt from the lake on it, it must of taken a week to get it off, sure hope it doesnt start to rust these old bodies apart.

Just another view of the behind of these great cars , I doubt I shall be lucky enough to see anything like this line up again, unless I travel to the East coast and check the “Rolling Bones” group out.

If you ever get to Speed week, you will know that the evening meet up is a great way to wind down from the Hot weather on the salt, it was still hot out here in Wendover but a cold brew helped to cool you down.

Look at this, a gasser Corvette, there is a piece of History right there, who has ever heard of a slow Corvette? So this must be a heart attack to drive about?

” Any Salt with that Sir” This pick up with Beer Barrel grill got many looks and I saw this quite a bit blapping about at the Lake in 100 degree’s +.

El Cheapo is right but I bet he had a million dollars worth of fun on the salt?

This Business coupe was tough as old boots, loved the chop and look how nice and close the rear bumper is too, so much work in this car.

This long Closed Cab pick up had a nice Black Flatty in it with Dual carbs and 36 Torque tube headers, very cool and traditional.

Oh my, this was just the coolest Roadster there, loads of Patina, loved the Canvass top, raked and chopped windshield and the commercial lights with those Tractor Firestone tires.

How could I not take a photo from the other side too, this was in the parking structure of the Nugget Hotel and casino in Wendover, what a great show there every night for speed week.

Check this ride out and it sits so well too, had more white powder over this than a cocaine addict with a sneeze! Loved the Black steelies and white walls too.

The Flying Brick seemed to get all over the place, yet hardly any salt on it, I saw this cruising all over the courses of the salt flats too.

We saw this Model A Roadster on the way up to Wendover when we stopped for some grub just outside salt lake City, I was so surprised that a show car with custom metal flake paint would dare to take their machine on the Salt, but he proved me wrong, great little ride and it was fast too.

Tough looking 5 window Model A with a small block, cal custom finned covers, Sanderson style headers and a deuce grill with Louvre’d insert was a great attraction, I really liked it.

5 window parked up was covered in Bonneville’s finest, the roof wasn’t even chopped and thats quite a rare sight theses days, I wasnt a fan of them rims or tires but, each to their own eh?

This pick up was pretty wicked, loved the Patina and the stance, looked to have radar style 5 spokes and I bet this was a real smooth ride to where ever it drove up or down from.

I took this with my phone and wasn’t sure if it would come out any good, but am pleasantly suprised with it, this was a fun area to be in, just by the side of the Nugget Casino in Wendover.

Loved the smooth lines on the Custom Sled, this really did have a lot of work, Nosed, Decked, Frenched, you name it, funny to see the Salt around it like on the rim of a Sangria Glass.

You can beat a drum, you can beat an egg, you can beat an opposing soccer team, but you cannot beat a traditional 50’s Model A 5 window coupe, such a wicked ride I never tire of seeing.

All the way from Washington, this Highboy was a classy ride, a really nice 1932 Roadster with the deep Ford Blue gave it a Nostalgic style that is always popular no matter what year we are in.

Here is its twin Brother, No license plate else you would think this was the same ride, Instrument Dash is cool too, but, great minds think a like eh?

Now this is right up my alley, Road or Garden path, how can you not like this Roadster, the flatty sounded awesome when it pulled into the Casino parking lot, you cant beat the sound of a flatty.

Liked this Model A complete with Knock offs and traditional rear tail light , being fenderless makes this A-Bone look a lot taller as well, come in number 46 your time is up!!!!

I really did like this Roadster, the proportions were right, even the chopped Deuce grill shell was bang on the money and loved the 32 Headlights hanging from the side of the rails.

If you look behind the cars you can actually see the salt lake, so not that far away from all the action, Wendover is the place to stay if you are coming to Bonneville but, book early or camp out.

If you get to the Nugget Early, you can grab a good spot to park your ride as this is where the car show starts every night, it goes on all through the night too, always something cool to look at and everyone is super friendly too.

I was sat down at the start line on the short course, a Customer of mine that I made some Megaphones for in Lawton Oklahoma, said he would be there with his pops, its a big lake so doubt I would find him, well this chap stood next to me said. “Carpy” What the heck, he was only parked right next to us, small world eh?

If you can ever make it out to Utah, do it, its a great place to watch History happen and one of the most friendliest events on the planet, so glad that I had the opportunity to go.

Lee munro’s First run on the Indian.

This spins out at 138 MPH but gives you just an idea of what is going on inside a cage.

Well, this is how 435 MPH looks and feels, bumpy and squirley as hell.

Here is another angle from the cockpit.

89 Year Old grandpa has a go in the coupe, spins out but what a great experience for the chap.

Last Run for speed week, watch until the end as some great camera angles, loved the last bit filmed from the rear.

Spin out, sure gets Gnarly out there.

Double Indian Scout engine Motorcycle.

Lee Munro on the long course gets to 186 MPH

Here we are with a Thruxton R having a go on the salt.

So there you go, a fun time, if you can ever make it to the Salt Flats, just once, you will then totally get the experience that we did and watch History happen right in front of your very eyes.

It is something I shall never forget, Speed week was always a place I wanted to visit to watch Hot Rods and Motorcycles Race and now that empty box has a huge Tick through it.

Thanks for following my 2 day Bonneville Blog, many people let me know that they enjoyed the write up and I hope that just looking at the photos made you at least smile today.

This Brings a close to this chapter but thats not the end, as for me I am so lucky to live in Southern California, as there is a dry lake there called El Mirage thats 90 minutes from me, and will be venturing out there next month, but a fond farewell to Speed week as I now get it and hopefully one day you can get out to this infamous Lake Bed in Bonneville, Utah.

Join the SCTA and be a part of this great organisation, as well as help Save the Salt too.

http://www.scta-bni.org/

I might see you at El Mirage sometime, if you see me, come and say hello, always great to meet like minded people.

http://www.scta-bni.org/el-mirage.html

Thank you to ALL you Racers, the Teams and their hard working crew, the whole S.C.T.A org, the Bonneville Nationals inc and of course the people I met from my Old boss in Australia and my mate Shug & Ruby May, for getting there and breaking a record, what an awesome deal.

Hot Rodding started right here and thanks to people like you, it continues to grow and prosper with all your help and participation. Thanks for reading.

Bonneville Land Speed Racing is a unique sport that consists of very determined people who drive hot rods, roadsters, belly tankers, lakesters, motorcycles, streamliners, and even diesel trucks to "shoot the salt" in a simple quest to have their name added to the list of many record holders. Many years ago, the Bonneville Nationals Inc. (BNI) was formed. It's main focus would be to produce the annual "Bonneville Speed Week". The BNI hosts a spectacular week of racing each year in August, which is the highlight event of the LSR season. Speed Week consists of six days of racing (Sat - Fri), weather and conditions permitting. Entrants come from all over the world to participate in the week long event. Spectators are allowed to walk through the pits, view the vehicles, and talk to the drivers and crew members. Public parking is south of the pit area, on the west side of the race track, outside the cones. Be sure to bring a hat, dark glasses, sunscreen and shade from the sun. Don't forget a camera with lots of film/memory/tapes, because you will want to remember everything you see and hear. Binoculars are also a great idea since the race vehicles are at least 1/4 mile away as they travel down the course. The salt flats are located approximately 88 miles west of Salt Lake City, UT on I-80. The spectacular scenery and racing conditions at Bonneville make it one of the most popular areas in the world for speed. The colors, excitement, people and smells are some of the reasons we race addicts return to the salt, year after year. Better known as "Salt Fever". CATCH IT!

Model A was fun to drive on the weekend

Posted on May 31, 2017January 30, 2020 by Steve Carpenter

31 May

Well, memorial weekend has come and gone by so fast, although in that time I caught a head cold that whooped my arse and have only just got back to a level playing field.

So wanted to throw some photos up I took of my 1928 Model A Roadster that I have and over that weekend I removed the fenders and bumpers to give it a more post war 1940’s look, and right now I am loving this little A-Bone.

I have always been into old vehicles and Motorcycles since I was a kid, back in the UK I had a 32 three window Coupe and, as I went to school on the East Anglian side of Great Britain, I was very close to the American Airbases and actually learned to ride a motorcycle on one of the WW2 Bomber Runways in Rougham . ( Suffolk )

This Model A of mine is a fun machine, not the fastest in the world but thats what I didnt want, what i wanted was a cool period Hot Rod that would of been around Southern California after the war and young serviceman and women had all these New engineering skills from working on aircraft, boats and tanks etc that they used their skills to hop up their Jalopys.

This Model A has a few cool parts now to make it quite a traditional ride.

Breakdown of parts:

16 inch Kelsey Wire wheels

1939 Flathead V8 Motor

1939 Three speed gearbox

1936 rear radius Rods

1940 Ford Juice (hydraulic) Brakes

32 style K member

40 ford pedals

1948 F1 steering Box

1940 Ford steering wheel ( Limeworks Speed Shop)

2 inch chopped stainless steel windshield.

Converted to 12 volt system

Edelbrock intake Manifold

Two Stromberg 97 Carburetors

I still have more to do like eventually I shall be removing the radiator and grill shell and replacing it with a Walker radiator and a genuine 1932 deuce grill shell and insert, popular back in the 1940’s.

Then I hope to make some exhaust headers that will run outside the Roadster up near the doors, using 2 old 1936 Ford Torque Tubes, another 40’s hop up that was very popular back then.

This was and always will be one of my Passions, I was simply Born in the wrong country as I have always loved the American way of life, the people, the country and of course, the invention of the Hot Rod.

This was built in Memory of My MUM that sadly passed 2 years ago and if it wasnt for her, I would not be here, Mum loved sitting in my old coupe, she even got her arm stuck in the window, chicken winging one day as i had a 4 inch chopped roof.

Plans are for the exhausts, the radiator, and some cool 1949 Kaiser Taillights that I fitted into 1948 Chevy Bezels and will fit them in the back under the rumble seat.

I shall also be getting a Canvass Top for her, as My hair grease melts in the Southern California Sun!

Hope you dig my Roadster as many people love the same stuff I am into, Motorcycles, Hot Rods, ww2 planes, boats etc, anything vintage.

I will keep you updated on other things I do to my AV8 Roadster.

Hot Rods in New Zealand

Posted on March 9, 2017January 30, 2020 by Steve Carpenter

09 Mar

I have been into Hot Rods for Many many years, I stopped counting after the 3rd decade and, being a Brit, I dreamed of living in the Great USA and having my Own Roadster and eventually take a drive on the Dry lake at El Mirage.

I grew up in London, then moved as part of the London Overspill to the East coast of Great britain, and from there, I got the American bug- we lived close to the American Air bases, IE, Mildenhall, Lakenheath, Bentwaters etc, the village that we lived in (Rougham) had an old WW2 Runway, complete with control tower and Nissan huts etc, this was where they originally had 3 runways and this is where the:

47th Bombardment Group (Light)

322nd Bombardment Group (Medium)

94th bombardment Group (Heavy)

All took off from on their dangerous missions and many never returning, I learned to ride a motorcycle on the 94th Bombardment runway and it is still there today.

We attended many Air shows over them years on the USAAF bases and I loved the whole Americanism that was there, it was a little part of the USA right where we lived, one of the Airman at the show gave me a magazine to read and it was a copy of Hot Rod.

It was a Black and White magazine from 1951 and the guy stood next to his Model A Roadster looked a little like me. That was it, I was hooked and loved Everything American.

I still have that magazine and now I am living my dream, I am here in Southern California, where Hot Rodding was Born and I now own a 1928 Model A Roadster complete with Flathead V8.

In the UK in the 1980’s I had a Right Hand drive, Chopped and channeled 1932 Three Window Couple and that was my own little piece of California everyday, even driving for the first year with no floor and having snow or ice pour into the coupe whilst driving to work was a fun experience for me.

I am not the Odd one out here, people all over the globe Love the Nostalgia that an old car gives you and you cannot get much further away than New Zealand, these guys know their stuff and have the bug like me, but this time, the Whole family are gear heads.

I love it, so- today i wanted to share a little into what makes us tick and this video pretty much sums it up.

Enjoy your day.

My 1928 Roadster

Posted on July 27, 2016January 30, 2020 by Steve Carpenter

27 Jul

Well, here it is, my 1928 Roadster, with a Flatty hooked up to a 1939 Box. But, it needs some work and over the next few weeks, I hope to have this running well and driving down the road.

I shall be changing this to a more traditional AV8 Roadster of the era I really love and that’s post WW2, I will be selling the top and making a lower version with chopped windshield too.

I am looking forward to changing the look and this is pretty good shape too, even though it is cool, there is a lot of re-work that has to be undertaken.

There is the beloved flathead, the very first V8 came from ole Henry Ford himself, but the Motor sits too far back so need to move an inch and half forward to make it right and no vibration.

Below is a list of things that this A-Bone already has. But the note to the side is what I am changing.,

1938 v8 motor late 24 stud
39 rebuilt trans
40 ford juice brakes front and back
40 ford master cylinder
New hoses and plumbing
New shoes and cylinders
Edelbrock polished intake
Edelbrock Aluminum heads
Original A radiator modified – Changing to a Original 1932 deuce grill shell and insert later.
Rebuilt generator – Its junk so I have purchased a Powergen.
New Distributor
New battery – Battery is only 6 volt, so converting to 12 volt. And repositioning .
Original model A dropped axle
Original banjo rearend- been gone through- The Banjo is going to be changed for a Columbia rear end I have.
Rear drum locks
Original model A Steering column- Pulling that out and fitting an F1 steering box.
Stromberg 97 carbs only one hooked up
Electric fuel pump
6volt – Am changing over to 12 volt.
New cloth spark plug wires with rajah ends
1935 Wire wheels
New 1934 v8 caps
New Firestone bias plys
Original unsplit bones – Rears will be getting 1936 Radius Rods.
Slanted windshield- Will be replacing with a 2 inched chopped windhsield.
New Smithys dual mufflers- Replacing with Race headers and New pipes.
Original Points ignition

Limeworks 40 Ford steering wheel.

New X member and re worked pedal assembly.

The electrical is a disaster, the guy who had it did a terrible job and I am having many power issues now and am trying to source the issue as this is still a 6 volt system, so nothing wants to turn over long else the battery will die. This is all going to change as I shall have it converted to 12 volt as it makes for far more easier starting and can see at night with no dim Glow from 6 Volt bulbs.

This will still need a ton of work and I hope I can get there soon as I want to be able to drive it in the next month or so as I love the look, just mechanicals need sorting.

I shall be fitting a 2 inch chopped windshield and later get a chopped top for it and of course I will lower the seat a few inches to allow for that.

Above will be the New X member that will be going in place of the shoddy one some fella attempted at welding in with some cheap stick welder, so this is going to be gone through and make sure all is safe and strong, as my Girlfriend will drive it too and need it to be roadworthy, right now I have a few issues to get ironed out but will get there bit by bit.

The Motor is now going to be moved forward, as well as the rest of the running gear, the Muppet who originally fitted the flatty put it back too far and the motor was pushed against the firewall.

Takes time, Money and Patience but I shall be keeping the Roadster in memory of my dear MUM.

I will run with No bumpers later and will also be taking the A-Bone Radiator and Shell out, and replace with a genuine 1932 Grill shell and insert as I have always loved that look.

This will be such a fun Hot Rod and dream of the day I take it for a run across El Mirage dry lake later on, as thats been a dream for so many years.

Above, 1936 Rear Radius Rods, these will be fitted to my Model A to give it much added strength for the V8 Flatty Motor.

Later on I shall be making this 1936 Ford Dashboard, fit the 29 Model A Gas tank, as I love this Post war style that was popular in Southern California back in the day and will simply swap out once painted and gauges fitted etc, but that’s a little later on down the road, but exciting stuff none the less.

I want to make sure this A Bone is safe and with a X member I know the chassis wont be flexing as much, as I have seen so many crack over the years on the shitty roads we have here in California as the freeway beats Hot Rods up for sure.

As you can see, the body had to come off for a number of reasons, and one was to move the engine forward and secondly to be able to fit the X member and over riders correctly, glad we have got to this point,

A better solution than the crap that was one there before, and also Bungs were welded in chassis to make fitting Roadster body easier.

Up in the air and soon to be laced back on the strengthened frame and I will be feeling a lot happier for that.

Flatty Motor is a 24 stud 1939 Era with Edelbrock heads and intake with three 97 Strombergs, The Radiator fan is now replaced with new bearings too, and the 6 volt system has been removed and 12 volt system now lives there with a one wire powergen to make sure I have plenty of electrical Voltage.

My 28 Roadster Body is in pretty good shape, Later on i shall be replacing the gas tank with another as I will be fitting a 1936 Dash in the old gas tank area.

Looking forward to when she is sat back on the rails and can get on with a few other things as she will be having 1936 Ford wish Bones on the rear and I have a 2 inch chopped stainless steel windshield to fit, along with a 1948 F1 steering box with a Limeworks 40 Ford style steering wheel.

The 1936 Rear Bones were cut and shortened and the welded and will make a big difference in the Rigidity on the rear end for sure, as this is a proven Formula from back in the day.

The complete X member kit is now in place with Boxing plates and this really is a good thing for me as I will feel a lot safer, I have seen many stock Model A frames that have stress cracks as they fitted a Flathead and the power does cause a lot more stress on the chassis, this was a Hot Rod Fab back in the day too.

Well, the stock winshield posts have gone and now a 2 inch chopped Stainless Steel set up is in place, looks way better now and am stoked to have it on the Roadster.

The Body is about to be plopped back onto the rails, all the old nuts that sat under the frame have now been replaced with threaded bungs, so no more struggling to hold the nut with a wrench under the chassis.

Now I have the 1936 Ford rear Radius Rods in and the Handbrake cable from 40 ford to Model A in Place, things are getting closer to be finished.

Slave cylinders are all good , as is the brake shoes etc, bit of adjusting to do but on step closer to getting her ready for a road test.

New fuel line will be added to the pump, filter and to the Strombergs.

New OEM 1939 Fan assembly but with New bearing and to help with Battery, a New Powergen, this goes from a 6 volt ride to a 12 volt.

Limeworks 1940 Ford steering wheel will be fitted to the F1 Column I have and wil be smooth to turn now, before, the notchy A Bone Column was a nightmare.

I shall keep the Model A Grill shell for a little while but have a genuine 32 one to replace it.

Reworked Model A pedal assembly will be fitted today, then the handbrake will be made to fit the 39 gearbox and a New floor to be added too.

Bit by Bit she will get stuff done, wont look much different but will handle so much better than it did when I first got iy.

Hope you like how she is turning out, this is something I shall keep as it is in memory of my Dear Mum!

Steering Column is in, just needs the tube cover to go on but it looks the right height, although I want to lower the seat somewhat.

I am glad how everything is working out as this needed a lot of work that someone had thrown together badly.

I have a Limeworks Steering wheel on that F1 Column and it looks great, great value for money. Also fitted 40 Ford pedal tops to Model A pedals.

Looks great in Black and White photo and wont be too long now before I can have a test drive.

Next up was to make a handbrake for the Rod, as there was not one in it at all, so a hunt for a few parts was needed as this A Bone now had Juice brake, lucky for me I located the handbrake, the wires and attachments as I need to be able to have a handbrake in this Jalopy.

Sat back on the floor for some more work, wiring needs to be addressed and as she is now 12 volt, make sure the bulbs are changed in the 6V lamps etc.

Bit more done but the battery will be repositioned, then, new wiring as well as securing the F1 steering box and fitting new switches for fuel pump and ignition etc.

Up next was some floor work that needed to be rectified , as the original is just wooden and I did not want that, this body is now sturdy to the chassis since the X member kit was added, and the doors will not pop open like many stock version do when the Ford goes up a drive way hill or a dropped kerb etc.

These are hand rolled and sure look nice in steel rather than ugly timber.

You can see that the Model A pedals have been reconfigured and now have 40 Ford tops on them.

Feels more like a Hot Rod now, rather than a Resto and will not be long until I can test drive her.

The Motor now runs and is smooth, only running the middle Stromberg right now but hope to use all Three later on once all the bugs have been worked out, straight through pipes for now until later in the year when I remove the fenders and run as a high boy and will use 1936 Torque Tubes for the headers like they did back in the Dry lakes days.

I am so glad that she is running Now, sounds quite smooth now that is fitted with a New Old stock fan and as she is turned from 6 Volt to 12 volt, she will fire up a lot easier and no more dim headlights.

Well, time has just tocked on a few days and I am glad to say I at last got the chance to drive it for the first time yesterday, mind you it was 100 degree’s outside.

Sitting pretty, this was a big moment for me, I dreamt of having my own Roadster in California for ions, and now here I am and its great.

She sits well but have to tell you, the rear shocks are shot to bits, so I will need to find some slightly longer and robust versions, maybe Pete & Jakes, but have to weld on shock mounts as the person before set these up for standard car shocks with no clevis at the top, but that’s all repairable and even though it bumps pretty hard, its so much fun.

I am happy at the style right now as I parked it outside my Motorcycle shop in Anaheim, it was 100 degree’s but I still drove it around and smiled all the way.

I will eventually remove the fenders and grill and fit a Genuine 1932 Grill shell and change lights and that is what Hot Rodding is all about.

Looks way better with the 2 inch Windshield chop and eventually I will get a retractable top but not just yet, but- I do need to cut the seat riser down about 4-6 inches I think.

The seat is Bone stock Model A and I sit too high, but I will try and locate another seat Riser and channel it a few inches to sit lower and have that early look too.

The flatty runs pretty good and right now, just on the middle 97 Stromberg but hope to hook the other two up at a later stage, once I have worked all the bumps out.

Having a bit of fun with a 1956 Flying Cloud Airstream,as these are the coolest trailers and easy to tow because they are so light and balanced well.

Yes- reverse does work and had to get used to the old style clutch pedal and it worked really well indeed on this AV8 Roadster of mine.

This looks like back in the day as I put it in Black and white, Classic lines and thought I would share with you.

Eventually I will locate a 1940’s trailer and be able to tow it to the dry lakes.

My Girlfriend loved it, it was fun driving it on the road for the first time, albeit 100 degree’s out and I live about 13 miles from the shop, so as I pulled into our street the radiator started to puke hot water out of the top cap, but that’s to be expected from the summer heat. All was good later on in the evening when I drove it around the block with Jen to try it out.

I have more plans for the Roadster, I will change the Radiator and the grill shell for a 1932 version and will remove the fenders too, then use 1936 Torque Tubes for headers and run them out the sides for an older style of Hot Rod, the car is always an on going challenge but that’s what Hot Rodding is all about.

So stay tuned for more on my 1928 Roadster…………………..

So now its time to get a few miles on her and work all the bugs out of it, that all takes time, money and patience.

Hot Rods are part of my Life too !

Posted on March 4, 2016January 30, 2020 by Steve Carpenter

04 Mar

OK- many people think that I am only into Motorcycles, and I can understand that, as I have been building Cafe Racers here in California in the last 14 years, but- since I was a youngster, I had the Car bug big time.

I grew up near to many American Air force bases and that’s where I got my first influences from of cool old American cars, I loved everything about the cars, the country and the lifestyle as well as the passion for Hot Rods.

Then, I had my first Hot Rod, a 1932 Deuce Coupe, it was Chopped and channeled and was a Right Hand drive Model, this Deuce meant so much to me and I felt like I was living in the U.S.A. with that ride.

I wish I had kept it now, as we all do when we look back at things we have had.

This was my ONLY form of transport and I drive it in all weather, I didn’t have a floor in it for a year, the snow and rain used to blast up inside the Coupe, until I lost a couple of cassette tapes and then my keys jumped out of the ignition as I was driving back from work and that’s when I decided it was time for a floor.

This used to be so much fun blasting about Brighton and I traveled all over the UK in my 3 window and some super fun memories that’s for sure.

I was a lot thinner back then, maybe from pushing the damn thing when the battery dies or I ran out of gas as my gas meter did not work.

I drove up to Hemsby for the traditional Rock n Roll weekender and then visited some old school mates and friends in that area, it was such a blast to drive, loud old and bumpy but that’s an old traditional Hot Rod in the 1980’s in Britain for poor working class folk like me.

The I-Beam axle was a 4 inch drop and shorty shocks, made sure you didn’t fall asleep at the wheel when ever you drove this Coupe.

Watch ya head, this coupe was chopped and channeled and with a 4 inch windshield, not much vision, plus when it rained you couldn’t see anything, and- to get me through the yearly MOT test, you have to have a windshield wiper, so- I took a complete motor and wiper arm off a Volvo Headlight and fitted it indie the coupe, it was perfect.

Such fun times and glad I actually took some photographs, else they would just be my own views in my head.

We were all a close knit community and had so much fun at Rock N roll weekenders, especially on the beach etc.

How about this shot, many many moons ago with my First car, a 1961 Low line Ford Consul, with a 4 banger and a 3 on the tree, I drove the lug nuts off this machine.

Oh dear- what was I thinking? But this was my 1959 Ford Zephyr that I 2 door-ed and made some mad steel fins on the car, this had Candy Red and white tuck n Roll too, I was in a crazy zone when I did this.

This was me in 1997 when I moved to Australia, and I bought a 195 XP For Falcon, very similar the the American Ranchero, this was a cool ride, they call them Ute’s out there but it was a fun ride that I played about with and really liked that car.

I used to pain the old race style numbers on the doors of my rides back then, I still do on the bikes I build sometimes, this time I painted the car flat black in my mates driveway and then fitted pin line whites and then fitted a cool set of MOON discs.

But I get restless and have to keep trying things out on this machine.

I cant leave anything alone for too long, this time I scalloped the car and pin lined it, as well as fitting a steel sun-visor.

I fitted a Black Tarp on the back and later on I located some fender skirts for it too. Then I painted the Coop Devil on the back and added more scallops!

But I will always love tinkering with stuff, just the way my Brother and I was bought up, not really had a happy child hood but kept busy.

I started to get into this Roadster when I moved to Australia from the UK in 1997 and then continued over here in the states as I shipped the body over, the photo above is me in New South wales, I was patching the side of the Roadster body as it was completely shot with old bullet holes, but- I wanted the same thickness steel and the contour, so used a 1940 Ford truck door to use and it worked out so well.

Above, Anthony Castaneda of the Infamous Shifters gave me his old Dodge Dash Board and I spent the next few days cutting my old gas tank and fitting this set up, I was so stoked to have accomplished this and loved the way the dashboard flowed, similar to the 1936 Ford versions.

I used a Belgian Flat head in the end and this was a great motor, I love the sound of side valve motors, a very unique sound of their very own.

Jeez, this was a while ago, i was wearing a watch, who wears watches any more?

I chose a eggshell Blue and a Flat white firewall as it reminded me of the Al Sharp Coupe.

I also had My 1958 F150 short bed painted by Anthony Castaneda in his old shop (RIP mate) I stayed up and hand painted the logo and lettering getting ready for me to go with the shifters to Paso Robles back then.

I will have to look to see if I have any more photos of this 29 Roadster of mine, I loved that car but had to sell it when everyone moved out to go forward in their lives and I knew I would have another later on.

I had so much fun building this in the garage at home in Southern California and sure wished I still had this Roadster.

Days of old but soon I will be getting back into another 1929 Roadster that I located in Indiana and My Girlfriend Jennifer Bought for me,I am looking forward to driving it with her in the following months.

This was a fun build and now resides in the land of the rising sun, sure hope to see photos of it as I sold it to a very cool friend of mine Ken Sakata.

I now have this 29 Roadster at my shop, needs a ton of work but- I will get there eventually, once I have located all the parts I need.

I have a super amount of work to do to this little A-Bone but it will be worth it and cannot wait until I can get onto El Mirage and of course one day at Bonneville Salt Flats.

I am not sure what color it will be but I will be running a Flathead, not the 4 Banger that’s in it right now.

My plan is to locate a cool Vintage dash board, be it a 36 ford, Chrysler, Pontiac or Caddy etc and have a unique look to it with cool Gauges.

I will be running a 1932 Truck grille, so that will all change but will still use original chassis etc and Kelsey wire wheels of course.

I have an original Moredrop axle for the front but will need 1940 Ford Hydraulic brakes all around too. And below, I was so fortunate to locate this Original plaque that used to be on the guys Roadster back in the day, a nice bit of history right there.

I will be using old plates as well to capture the spirit of the style that I am into and hope that this will make people smile once completed.

This will be a cool build but maybe a year before I am halfway there I believe, hard to do on a low budget.

But stay tuned, as i will up date when I get more parts together etc.

GRAND NATIONAL ROADSTER SHOW THIS WEEKEND.

Posted on January 29, 2016January 30, 2020 by Steve Carpenter

29 Jan

On Sunday, Jennifer and I will be attending the Grand national Roadster show, of which I was lucky to WIN trophy’s Three times for my Cafe Racers, but, I have always been into Hot Rods and back home in the 80’s I had my very own three Window, chopped and channeled 32 Coupe.

Well, I now have a stock 1929 Model A Roadster, More Rust than I really had thought and needs a total strip to the frame and will fit a flathead etc and what I have been looking for is a cool color, I love Black but many out there, I love Blue but built a 29 Roadster in early 2000 and that was Blue.

This was a great ride but had to sell it when bills at the house got out of control and I sold it and it ended up in Japan where it still is today.

I am hoping to get the Roadster into a Vintage style by Next year with any luck and of course, in Memory of my Dear Mum of which if it wasn’t for her, I would not be here.

So I have been looking at Car shows with Jennifer and of course any where I see a Color that jumps out at me to try and think of what would look great on my Hot Rod. Jennifer and I both thought a WW2 style Green would be different then I saw a buddy I know has just completed his 32 and painted his Green, and this was the color I looked for over the months, so may have to go a little darker, but this 32 Roadster is so nice I had to share it with you all. I love this Hot Rod and am sure you do too.

This weekend and Its going to be a super show with many cool rides for everyone.

Mine will never be as cool as this but will have fun with my ride for sure so, wish me luck.here is mine right now. she needs tons of work but it will be a fun machine later.

Below is what HOT ROD wrote about this super cool set up and I wanted to share this with you today, if you are at the GNRS on Sunday drop me a text or message as I shall be there with Jennifer and would be awesome to see you.

Some of the best advice a father can give to his son is the phrase: When you want to learn how to do something correctly, watch a professional do it. The “right way” is nothing that can be taught by reading a technical book or even watching a YouTube video, but rather hands-on immersion and a learn-by-doing mentality.

Darryl Hollenbeck, a 48-year-old automotive painter who grew up in Concord, California, had a distinct advantage when it came to learning his craft: his grandfather, uncle, and father were all car painters, with Dale (Darryl’s dad) carving out a respectable niche in the custom car world before he died in 2003.

Now known as the “go-to” guy in Northern California for many of the country’s top rod builders, Darryl’s paintjobs have been found on an America’s Most Beautiful Roadster award winner, dozens of STREET RODDER and Rodder’s Journal cover and feature vehicles, and well as a handful of Pebble Beach Concours d’ Elegance show winners.

But Darryl’s approach to all these cars is the same: it’s all in the details. As owner/operator of his Vintage Color Studio in his hometown, Darryl usually works by himself, perfecting any given body long before the color ever leaves his spray gun. But he’s also a car enthusiast and, after working on dozens of vehicles over the years, he really wanted a hot rod for himself, but time, the job, and money always seemed to get in the way. He did get close a few years back, starting a 1932 roadster project, but he ended up having to sell the car well before it got finished.

Recently Darryl’s friend, Brandon Flaner of East Bay Speed & Custom, told him about a project that someone had lost interest in. It was another Deuce highboy roadster, with a standard street rod build started but not finished. Darryl bought the car but soon realized, considering his workload, this one may not get finished either.

As fate would have it, one of the cars slated to roll into Vintage’s paint booth was a Deuce highboy from Cory Taulbert. The Michigan native is a part-time rod builder and married to the former Ashley Webb, she’s the daughter of fabricator (and former Ridler winner) Dan Webb. As anyone who knows Dan can attest, he likes a good joke, and when dialing in the drop-off times for the roadster to get painted, Dan half-heartedly suggested Darryl trade the paint- and bodywork on Cory and Ashley’s roadster for the build and fab work on Darryl’s ride.

Not wanting to potentially ruin a good friendship with Cory (as it happens sometimes in these situations), Darryl discussed the trade with his wife, Terri, and the pair decided it was probably the best way to get his car finished, so they said yes and, in February of 2014, the swap was made. Once at Darryl’s shop, he started working on laying down a perfect single-stage black paintjob on Cory’s ride, and Darryl’s roadster ended up in Michigan at Webb Automotive Art and up on Dan’s chassis jig.

Though sufficient for a basic street rod, most of the items on the chassis would be out of place on the style of car Darryl wanted to have, so the SO-CAL framerails were left, but just about everything else, including the X-member, was removed. In went a 1940 Ford X-member, which already had provisions for the correct pedal assembly Hollenbeck wanted, and the rear was kicked a little to lower its stance and accommodate the Model T spring.

Dan and Cory also installed a Rodsville Halibrand-type rear (4.47:1), which was prepped and painted by Brandon Flaner. The rear featured Dutchman axles, and is located with a custom three-bar system (two lower outer rods along with an upper center rod) built out of split 1940 wishbones by Cory, who also fab’d the Panhard bar.

MT Products’ 1940 Lincoln-type drum brakes are on each corner, and a transverse spring and SO-CAL shocks smooth out the ride. Steering is handled by a Vega box and a LimeWorks column, and original 1940 Ford 16×4 wheels (wrapped in Firestone 500×525 rubber) were used up front while 18×4.25 wheels were shod with 700-18 tires.

Darryl turned to Edelbrock for one of their 380-horse crate motors, which was outfitted with an Edelbrock 2×4 intake manifold, a PowerGen alternator, and an MSD ignition with Taylor wires. Cooling is cured with a Walker radiator and Cooling Components fan while stock ram horn headers and a custom 2-inch stainless steel exhaust removes unwanted gases. The V-8 bolts to a T5 BorgWarner transmission, prepped by Astro Performance. What chrome there is on the car was handled by both Tennessee’s Advanced Plating and California’s Sherm’s Custom Plating.

The 1932 body originally came from Brookville Roadsters, and Dan and Cory fit it with Rootlieb 25-louver hood sides, a sectioned hood, and a Brookville Deuce grille shell and insert (with a custom center bar). More custom fabwork can be found inside the cockpit, with Dan fab’ing gloveboxes for the ends of the Deuce roadster dash, which was also lengthened for the Stewart-Warner Hollywood five-gauge insert that features a big Police speedo. Cory also modified a Model A shifter to work with a Pro 5.0 shift tower, and DynoTech supplied the driveshaft.

Once all of the fabrication was complete, the roadster was returned to its owner where he and Darrell Schneider prepped the ride before Darryl added the color, which, along with its stance, may be the most important thing about the car. Most folks toil with the choice of color for their rides but, with Hollenbeck being a well-known painter whose choice would also make an obvious statement, color choice became critical.

Not wanting what someone else already had entered into the decision picture, as did making sure the wife liked it, too. The roadster had a lot of traditional elements, so something that looked like it could have rolled out on a Lincoln in 1940 would be going in the right direction. All said and done, Darryl mixed up his own unique shade of brown with PPG Envirobase waterborne paints to cover his car.

Once out of the paint booth, construction continued with help from Joe Compani and Ryan Campi of Compani Color (who prepped and painted the chassis), as well as Jack Stratton, plus Bill Ganahl and his team at South City Rod & Custom, who helped with final assembly. Next came the addition of a one-of-one Bop Top from Sid Chavers (the bows were repositioned), the chopped windshield posts from Cory, a set of Guide headlamps, and a pair of taillights and door handles from a Chrysler Airflow. A LimeWorks Crestline steering wheel fits the car’s profile, and a multilayered chunk of paint from Darryl’s father’s paint booth was turned down on a lathe to produce a one-off shift knob.

Cory Taulbert flew out to NorCal to wire up the roadster using pieces from Rhode Island Wiring Service harness and an Enos panel, and Sid Chavers created the bench seat in the car before covering it with sections of leather as well as a fabric insert piece from a 1969 Cadillac.

Both Darryl’s and Cory’s roadsters were finished up (Taulbert got his dream paintjob—an inky black one-stage for his Deuce) and the pair decided to debut their rides by driving them from their respective states to the Roadster Roundup in Austin, Texas (a 3,400-mile roundtrip for Darryl), in 2015.

But for Darryl, just as important as delivering a world-class paintjob is making and maintaining the friendships he’s fostered throughout the years. For him, he wouldn’t want one at the expense of the other and, luckily for the rest of us, he’s really good at both!

Grand National Roadster Show:

POMONA FAIRGROUNDS

CALIFORNIA

Mooneyes Christmas event Irwindale

Posted on December 15, 2015January 30, 2020 by Steve Carpenter

15 Dec

Well, Saturday Morning soon came around, a little apprehensive about the trip to Irwindale today as yesterday we had Rain on and off all day and the forecast was dry as a proverbial bone.

But it was a nice morning and no sign of rain, but, we came to the decision to jump in the wagon, and head out to the freeway and see what this years Mooneyes show had in stall for us, on many occasions the sky’s have closed and it has poured down with H2O, so this time we were prepared.

The traffic was pretty good on the 5 and the 605 was even more clearer, so it took us maybe 25 minutes to make the trip to the Drag strip, but there was the usual line to get in and, I could see there was many vehicles already at the show and knew that this event would indeed be a doozy!

We parked on the Oval track where they race the Speedway, so kinda cool being lined up on the third turn and headed down the incline, trying not to walk like a professional shopping cart pusher.

Once in the show, the air was filled with BBQ and Hot Dogs, as well with a good sprinkling of Rockabilly Music, and high revving cars as they staged and drag raced up the 1/8th mile strip.

So many cars had turned up and it was fun to walk the lines of machines, checking them out and seeing what the trend is this year in the Custom world and I noticed a few Lavender painted cars in a flat finish, so that seems to be the go this year.

Mooneyes is always a fantastic annual social event for me and was great to be able to approach some well known names in the Hot Rod industry, just to shoot the breeze etc.

Shige from Mooneyes is always there and will stop everything he is doing to chat and genuinely ask how you are etc, so great to see him and Chico, along with Bob and Go manning the busy station, selling their infamous wares.

There were many vendors this year and ranging from cool plaid Pendletons, to custom pomade, there seemed to be a little of everything at the show and was a enjoyable checking different vendors booths to see what they had created for sale.

I saw Vintage Hot Rod Club Coats I would of given three arms and a leg for but wrong sizes made it a unsuccessful scavenge for me this time but, proves that there are still wicked clothing out there if you are at the right place at the right time.

I saw Big Nick Barns, another Ex pat living in SoCal and has been dealing in the Vintage Clothing industry over 30 years and always seems to come up with unique apparel and love seeing it.

Jennifer and I watched Buddy Dhugi and his wonderful wife Suzi, play as they always do for the moon show and this year kitted out with Christmas sweaters, albeit it was bloody hot this year.

But their set was pretty cool and they rocked the event as they usually do, we made sure to stop and chin wag as these are the best events for an annual social gathering for us.

Next band was my mate Big Dan and he plays in the Dynotones, an awesome 60’s Surf Guitar combo and boy do they rock, loved every song and hope to book them for my annual party in march 2016.

We grabbed some food and hung out with some good people, I spoke to some mates I hae not seen in years, like Dean from Dice Magazine etc and Dennis Roth was in his element having fun with people in his Crazy Custom Flaked machine.

The sound of bands playing, and Gassers racing up the strip every few minutes is an awesome experience and one you should at least try Once, just to be able to truly understand what I am on about, it is a really cool show- busy but cool.

So many cars to see, make sure you allocate a few hours just to observe these fantastic machines as we walked isle upon aisle and people were more than happy to tell you about their car and how it came about etc.

Now this Roadster you see is a show car, something many of you and I dream about, Jennifer asked the guy if it was his and with a smile on his face he said yes.

I asked him about the 40 ford dash and he said it was a 40 ford dash but- he did not build the car, he won it in a raffle.

I was gobsmaked as i remember the Roadster being as a raffle car at Ventura a few years ago, he said he had watched the Roadster being built via instagram etc and he bought ONE $20 ticket, he went to the show but came home as it was his 32nd Birthday, the phone rang and he thought it may be one of his buddies wishing him all the best, but infact it was ventura asking him if he had abought a raffle ticket for the car. He said yes and then she said, well you have won it!!

Jeez, for $20 a $40,000 Built Roadster, they even had the builder drive it to his house and he drives it every weekend, lucky man, I always hear about raffles and never believe they are legit and you never see the winner, but this was the real deal and for $20 he won that awesome machine.

Jenn informs me she is doing Raffles from now on and, I tend to agree with her it seems like it may just be worth the chance, but such a great story on that Roadster.

Mooneyes always brings over their super cool pinstripers from Japan and they turn out some super cool work quickly.

A great event and so much to see, make sure you get here early to be able to take it all in.

Another Pinstriper is Hot Rod, he has been doing this for many many years.

This Blue 29 Roadster was pretty cool parked up and sun bathing.

I loved this tough 55 Gasser in Candy Paint, sure sounded menacing too.

This mid 60’s Ranchero was so bang on the money for styling .

Legends in the Hot Rod Art world, Robert and Suzy Williams were in attendance too.

Here is my mate GO hat works at Mooneyes and is a super nice fella.

Organ pipes on this roadster sounded like a broken fan in a fridge.

29 roadster pick up but too low to pick anything up.

This green T was pretty cool.

Another channeled Roadster sits on the deck.

Now, I would drive this home no problem.

A nice sprinkling of Roadsters were here this year.

A few Custom Low riders too, a lot of masking to do this.

Like I said, there are all sorts f machines here, enough for everyone’s taste.

Well, it is the Christmas show.

Now this is what I am talking about, I love the straight Axle Gassers.

This was a sweet 58 I would love to own.

Amazing, as I live in SoCal, youd think you seen all the rides and then you come to Mooneyes show and loads of cool stuff not seen before.

Plenty of Chevys thats for sure.

I dug this pick up, would be a fun parts ride.

This was pretty cool to see and I am sure he has fun with it with that Motor.

Even the Old Bill were cool.

Loved this Kustom Pontiac.

Nice color scheme I thought.

Always great to see some classic Tin here.

Frenched Lights and a floating grill was cool.

These are Custom from right out of the show room.

How can you not like this Lincoln front end.

Always loved these and the body goes on for miles.

Now this is right on the deck.

Rather odd choice of color but it works.

Loved this 57 Belair as a gasser, the best years for me for gassers are the big straight axled heavy Bricks.

Slammed Custom Roadster for the use of a better word.

Three hungry birds.

I loved the artwork on the trucks door.

How clean is this and I love the color.

This sedan sat really well.

The sun was out and so were the Hot Rods this weekend.

A cool 56 Gasser awaits its turn before going up on the 1/8th mile.

This 1948 Rag top was cool as hell and loved the color.

A couple of car club guys shooting the breeze.

Off the the strip to tear it up.

This Caddy is pretty straight bodywork wise.

A Candy red 58 Pick up look good basking in the Sun.

Now that’s a lot of work.

How straight is this and love that color.

Some intricate masking here to get this effect.

I think this is Keith Weesners 5 window and boy is it nice.

Suicide doors on this Bow Tie.

Whats going on here, his own Smoker?

Clean, low and bell flowers too.

Nice 56 for belting around town in.

So clean.

Jeez, that push bike must weigh a ton?

Yep. that will give it some giddy up.

Thats one way of making sure the hood closes on that Caddy.

More random shots for you lot.

I am way digging that color.

Matt from Australia’s ride that he painted himself.

Plenty of GM rides here.

Different and nice to see from the Norm.

Hanging in some shade on this hot day in December.

Plenty of flake in this design, so many hours.

This is one tough looking 58.

Plenty to see today.

Antique Nationals at Fontana was a Blast to watch and be a part of.

Posted on June 29, 2015January 30, 2020 by Steve Carpenter

29 Jun

The Antique nationals Annual event seemed to come around real fast this year, but it was not to disappoint as many cool Hot Rods turned up for this Classic meet up and Jennifer and I headed out about 10am to get to Fontana Drag strip to watch some of these Nostalgic machines run the 1/4 Mile. The A-Bone was a great looking ride and the owner had had this for many many years, having a Hoped up 4 Banger is such a rare sight these days and glad to see it. It had some later parts like Alternator and a Thermo fan but this car runs and runs very well indeed. Three Hungry Birds sat on that Early Cragar intake and made sure that this 4 Banger had plenty of Motion lotion to get up the track in a good fast time. I loved the dash cluster and rebuilt Gauges made sure that these all gave a correct reading out in Fontana as it was almost 100 degree’s here today. I am not a fan of 4 bar set ups but loved the hairpins and steelies for this 1929 Roadster on stock rails too. Early style roof gave it that early 50’s look and running a Quick change really does make this Roadster get up and go !!! I loved the Original License plate with the Glass 1939 teardrop lights, this Rumble seat Roadster was a sure cool piece of History out here. This Girly put her Roadster together a few years ago now and with the Caddy mill it made that awesome throaty roar as it roared up the tarmac. Blown Model A Pick up sure got down the strip in a fast ET and surprised a lot of people. Squeak Bell the Kiwi from Bakersfield bought out his awesome 40 Ford Coupe, I loved this ride, pure 50’s Nostalgia all the way through. This little Model T Roadster came down from Arizona, he ran a 302ci Ford and Jenn and I sat in this and felt like giants in it. Many Gassers were here for the day and loved to watch them go down the strip as the weather was humid but great for watching them fly up the 1/4 mile. What a Great match up we had here, I call it the Double A challenge, Roadster Pick up and the flamed A- Bone hit the strip and ran even all the way. It was fun hearing these 4 Bangers wind up as they get off the line and am surprised as to how they flew up the strip and sounded awesome. Plenty of 4 Banger Machines to entertain the crowd today and a rare sight to see at one time, sure glad we made the trip to watch these race each other. How can you not like the Gasser wars? These are always a blast to watch and to hear as these bad boys tear it up at Fontana . Loved seeing this 56 Wagon tear it up at the strip and a very cool set up this was, a rare sight these days. Hubba Hubba! Check this Roadster out- other than the tires I would of left it as it was, a real History machine that was a trip to look over. Have a look at this 4 Banger, how cool would it be to find one of these engines these days and then take it up the strip and then after, drive home, Very Cool. Some serious Tin here and not many like this around anywhere these days. There seemed to be plenty of early Cragar equipped Motors here today but it is run by the Four Banger Club but a rare treat to see all this together. Plenty of engine variations to look at here and had a great time chatting to all the owners etc and asking them about their machines. The weather stayed humid but lucky the Sun was shielded with low clouds, and that made for a great day of racing and pretty good for the spectator. Awesome 32 Three Window Deluxe Coupe as this Fully Fendered ride headed down to the staging lanes to run with the other flatheads. 5 window sits ready for the next round with steelies and spindle mounts, a very tough Coupe and an aggressive stance. Three Very different rides sit here by the Drag strip, Blown 29 Roadster, Stock Model T and an old Hudson Hornet. A very clean and well built Roadster, complete with hairpins and Drilled I- beam and moons discs looked the part here at Fontana Strip. Something for everyone here and we had a fun day chatting to the owners and finding out some info on their rides and where they got them from. Gassers at the ready as Dennis Young, the Aussie Racer drives his Anglia up the strip. Yes please to this Roaster, I would change tires and shocks and rake the windshie3ld but, that’s my preference a solid car and loved it. Another cool Flatty powered roadster that would look great on the driveway at home. This 24 Stud Flatty was powered with Early Edmunds heads and intake Manifold with what looks like REDS headers, cool Motor for sure. Model A Roadster Pick Up was really cool, I loved the 41 plate too. Yes Please. A wicked Roadster with the right look and a sweet firewall and grill shell too, very much wanted to take this home with me. I could not stop looking at this and when they drove it around, the flatty sounded tough, just a really Nostalgic ride for me. A super Clean 5 window that was also popular here at the strip. Plenty of Rare tin to look at here at Fontana and these three cruised about all day. Edelbrock Powered flatty, I really loved this machine and so glad we made the trip to watch the Antique nationals. This stocker sounded pretty sweet and was up for sale too. Still plenty of Tin around and that is surprising but of course, the prices are starting to soar now. This was a winner for me, how cool is this Roadster? I love it all and it sounded awesome. Ready to drive home to La Mirada, I would be so lucky. A Rare find Roadster and it is waiting for a New owner I am sure but I couldn’t afford the price ticket, else I’d of bought it right there. Loved the Canadian Ford heads on this 21 stud beauty. Banjo wheel too, I loved everything about this machine and glad I got to take photos to share with you lot on here. Bills Three window is just an original Time capsule, just enjoy and drive the wheels off it and Bill certainly does as he loves this Coupe. How cool is this? Such a Classic machine and still being driven daily . Look how straight the Bodywork is too, this Three Window is a super rare find and glad to see Original Tin on the road still. Early Plate and cool License plate frame too. Next time you are in San Dimas, check out Bills Three Window and shop- The Old Ford Store. Look at how clean this Roadster is, such a lovely machine in all Black henry Ford Livery. There is Nothing I would change on this Roadster, just take a look at al the detail in this, simply breath taking. I would of liked to hear this machine purr, but the old fella was out having fun with his buddies on the strip but just check this Roadster out, so sweet. Unchopped but Channeled 5 window is reminiscent of the old 60’s East Coast Rods. This Straight axle gasser looked Fast and was fast, loved seeing these race up here at Fontana and they didn’t mess about either. Jennifer inspects this Roadster with its beam axle and hopped up 4 Banger mill. Ak Miller Speed Equipment adorned this roadster, a lot of time and effort had gone onto this build., BRAAAAAP! Pat Gnahl on his Knees as he works on this sling shot straight 6 powered Dragster. This altered Machine was tidy and was pretty fast up the strip today. A very cool little Hot Rod that had a nice Quick Change too. Always cool to see these driving around and the air was filled with smoke and fuel at Fontana today. How can you not like this awesome Willys Gasser, Blown, Flat paint and running on Magnesium’s. Another set of Gassers and this certainly took your breathe away as he hit the loud pedal on the Line today! The Antique nationals is such a good event as it lets you get so close to all the cars and the action too. Below, the staging lanes with all the rides getting ready to compete into the next round. The weather was great later in the afternoon with a little breeze and plenty to look at as we walked around the staging lanes and Pitts. More cars coming down to the staging lanes as we walk around and enjoy the atmosphere at Fontana. Squeak Bells awesome Custom Coupe, Squeak is a well know Hot rod builder and is a Member of the Shifters Car club. Jeff Vodden and Billy Sakata of the infamous Shifters chat to Squeak Bell as he heads to the staging lane for his run today at the strip. 5 window heading down the the track to try his chances of getting through to the next round here at Fontana. This Channeled 5 window lets it all hang out as he gets the Green light and was a fun and fast Hot Rod. Plenty to watch, hear and small as these vehicles raced all day and we loved it all as such a great atmosphere here every year.. We need more of this event to watch every style of Hot rod take to the strip as it so much fun to watch or take part in. Pick up or Coupe, there was something for everyone here and could not get enough of this today. Maybe Next year I shall have my own Roadster and see how I fare with other like minded Hot Rodders. Above is a super Nice Stepside I would love as a shop truck. This 4 Banger A Bone was pretty cool other than the color and graphics but a tight Hot rod and sure was fun to see. The good thing about the Antique Nationals is that you can get and look at the rides close up and everyone is friendly. This ole fella had his Hudson Gasser all about ready to take up the strip. Always nice to have a flip front to be able to get to the Motor and this was a well put together machine and sounded great. This was indeed built for speed and he had great fun this weekend at the track. Another cool Shop truck and nicely done, always great to see these at the Drags and sometimes they even run them against each other too. The Little T that could, this was a low slung ride and driven daily too, up for grabs as well. Traditional 50’s styled A- Bone stood out, I mean, you cant miss them Pete and Jake style flames. But a great little roadster and I know that I would have fun with it and I am sure that you would do too. Every year there is always different rides that attend this show and I love talking to folk around the Pitts to see where they are from and something about their machine, it makes for an interesting and sometimes entertaining conversation. His Beer barrel grilled pick up was cool. Plenty of people were here to race and to have fun an this was a fun ride to watch this weekend and did not hang about. A lonely Roadster sits on the Tarmac awaiting its time, sits low being channeled and I loved it with red Oxide primer an all. This little A-Bone Roadster was super cool and so was the owner, 4 banger power with AK Miller parts, this will run all day and never get hot. I saw plenty of Ak Miller parts this weekend and love seeing cool stuff like that, this Roadster is daily driven in all weather and super nice owner. A fun little A- Bone that he gets many many miles of smiles from and I am envious in a good way, great to see and chat too. This guys doesnt give a flying Duck- loved the tear drop trailer with it, super tidy combonation. A lot of time and money have gone into this ride and boy can you tell, this was so clean, yet he drives it to many places. A very cool set up and never an issues in the time he has had it, just a well built machine and fun to see today. Cruising down to the Staging area to check out the rest of the rides. Resto’s were very clean and all of them run like a top. Something for everyone if you come to the Antique nationals and we had a brilliant time here. Love looking at the Gassers. It hauled Arse too. Super clean green machine and I have always dug Classic Fog lights on Rods and motorcycles. Tasty Three Window sits facing the drag strip to watch the Vintage machines scream down the track. A walk around the Pitts shows all sorts of amazing machines and this Black Three window caught my eye, its a really ride. 1932 was a great year for the Automotive industry, being the First V8 Fathead too, love these rides. Great Girder front end on this Whizzer and a few raced this weekend too. Super Nice Bowtie Step Side work truck, love these things and sits well on 5 spokes. Jenn and I sat in the Little Channeled Roadster, I was half hanging out of it but a fun ride and a super nice owner from Arizona. Mid engine Flatty in this push truck looked great. Two Door 50 Coupe was such a nice clean ride. I would of loved to have driven this today even had a push bar on the arse for the drags or dry lake. Every where we looked there were Flattys blappng about the place. A few Cushmans turned up too and ran like 35 seconds on the 1/4 and fun to watch race. This 5 window was heading out to the staging lanes and runs super well, More stuff to look and listen out for as we walked around at Fontana. There goes the Cushman- Flat out at 40mph. Whizzer and Harley go at it, thats fair right? We had an awesome time, and look forward to next year, hopefully see some of you out there too?